ACEPOM GROUP

Hotline:   +86-0523-84268368
               +86-0523-84222458
Product details
SKF Medium induction bearing heater TIH100M
Origin: Netherlands
Brand: SKF
Model: TIH100M
Brief Introduction: High heating capacity of up to 120 kg bearing
Product details

High heating capacity of up to 120 kg bearing

The SKF medium induction heater TIH 100m has the same high standards of efficiency and performance as the smaller heater TIH 030m, combined with increased capacity. The advanced design of the power electronics allows features of accurate electric current control, cut-outs to avoid overheating and controls on rate of temperature increase.

Placing the induction coil outside the heater’s housing allows the heating of bearings weighing up to 120 kg (264 lb). The heater is equipped with thermal overheating protection to reduce the risk of damage to the induction coil and the electronics. In addition to temperature mode, the TIH 100m is equipped with a time mode for heating components other than bearings. The heater is supplied standard with three yokes and is available in two executions: 230V/50-60Hz or 400-460V/50-60Hz.

TECHNICAL DATA
Designation

TIH 100m
SKF m20 performance

97 kg (213 lb)
Voltage, V/Hz
- TIH 100M/230V230V/50-60Hz
- TIH 100M/MV400-460V/50-60Hz
Bearing:
- Maximum weight120 kg (264 lb)
- Maximum bore diameter20 - 400 mm (0.8 - 15.7 in.)
Temperature control:- Range *
0 - 250 °C (32 - 482 °F)
- Magnetic probe
Yes, K-type
- Accuracy (electronics)
± 2 °C (± 3,6 °F)
Time control:- Range
0 - 60 minutes
- Accuracy
± 0,01 sec.
Performance example:- bearing, weight, temperature, time23156 CC/W33, 97 kg, 110 °C, 20m
Thermometer mode

Yes
Bearing mode

Yes
Power reduction

2-step; 50 - 100%
Demagnetisation according to SKF norms (automatic)

Yes (<2 A/cm)
Can heat sealed bearings

Yes
Can heat pre - greased bearings

Yes
Error guiding codes

Yes
Thermal overload protection

Yes
Maximum magnetic flux

1,7 T
Control panel

Key board with LED in remote control
Operating area (w × h)

155 × 205 mm (6.1 × 8.0 in.)
Coil diameter

110 mm (4.3 in.)
Dimensions (w × d × h)

570 × 230 × 350 mm (22.4 × 9.0 × 13.7 in.)
Total weight, including yokes

42 kg (92 lb)
Maximum power consumption

3,6 kVA (230V)
4,0-4,6 kVA (400-460V)
Number of standard yokes

3
Standard yokes

56 × 56 × 296 mm (2.2 × 2.2 × 11.7 in.), for heating bearings with bore diameter of 80 mm (3.1 in.) and larger
28 × 28 × 296 mm (1.1 × 1.1 × 11.7 in.), for heating bearings with bore diameter of 40 mm (1.6 in.) and larger
14 × 14 × 296 mm (0.6 × 0.6 × 11.7 in.), for heating bearings with bore diameter of 20 mm (0.8 in.) and larger
Core cross section

56 × 56 mm (2.2 × 2.2 in.)
Yoke storage

Yes, foldable
Sliding arm

No
Swivel arm

Yes, large yoke only
Cooling fan

No
Housing material

Steel and glass filled polyamide
* Maximum heating temperature capacity depends on the weight and geometry of the bearing or workpiece. The heaters can achieve higher temperatures, please contact SKF for advice.


Message submitted